®
JBL® ON AIR
CONTROL® 2.4G AW (230V)
OWNER’S GUIDE
IMPORTANT SAFETY INSTRUCTIONS
13. Unplug this apparatus during lightning
storms or when unused for long periods of
time.
14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way,
such as power-supply cord or plug is
damaged, liquid has been spilled or objects
have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
15. Do not expose this apparatus to
dripping or splashing and ensure that no
objects filled with liquids, such as vases,
are placed on the apparatus.
16. To completely disconnect this
apparatus from the AC Mains, disconnect
the power supply cord plug from the AC
receptacle.
17. The mains plug of the power supply
cord shall remain readily operable.
18. Do not expose batteries to excessive
heat such as sunshine, fire or the like.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves or other
apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug.
A polarized plug has two blades with one
wider than the other. A grounding-type plug
has two blades and a third grounding prong.
The wide blade or the third prong is
provided for your safety. If the provided plug
does not fit into your outlet, consult an
electrician for replacement of the obsolete
outlet.
10. Protect the power cord from being
walked on or pinched, particularly at plugs,
convenience receptacles and the point
where they exit from the apparatus.
Figure A.
Example of Antenna Grounding as per
National ElectricalCode ANSI/NFPA 70
11. Only use attachments/accessories
specified by the manufacturer.
12. Use only with the cart, stand,
tripod, bracket or table specified
by the manufacturer or sold with
the apparatus. When a cart is
used, use caution when moving the
cart/apparatus combination to avoid injury
from tip-over.
3
THANK YOU FOR CHOOSING JBL
For more than 60 years, JBL has been involved in every aspect of
music and film recording and reproduction, from live performances
to the recordings you play in your home, car or office.
1
3
MUTE
INPUT
0
2
VOL
We’re confident that the JBL system you have chosen will provide
every note of enjoyment that you expected – and that when you think
about purchasing additional audio equipment for your home, car or
office, you will once again choose JBL.
Remote Control
Please take a moment to register your product on our Web site at
advance-ments, and helps us to better understand our customers
and build products that meet their needs and expectations.
4
5
®
®
The JBL On Air Control 2.4G AW is an advanced wireless
loudspeaker system that allows you to enjoy your favorite music in
remote locations around your home, or to add surround speakers to
your home theater system without running wires to the back of the
room. To ensure trouble-free performance, please carefully read
these instructions completely before connecting or using the
system.
–
+
ID
CODE
1 2 3 4 TO RIGHT SPEAKER
UNPACKING THE SYSTEM
Carefully unpack the system. If you suspect damage from transit,
report it immediately to your dealer and/or delivery service.
Keep the shipping carton and packing materials for future use.
Open the package and verify the following contents:
DC 20V
SUB-OUT LINE-IN
Left/Active Speaker
(Rear)
LEFT-CHANNEL SPEAKER
Included
1 x Transmitter module
1 x Power supply for transmitter
1 x 230V 2-Prong AC power cord for transmitter power supply
6
8
7
1 x Wall-mount bracket for transmitter with 2 x panhead
M3 x 4 machine screws for attaching wall-mount bracket
to transmitter
4 x Small round self-adhesive feet – to be attached on
transmitter’s left side panel if transmitter is to be used vertically
–
+
1 x Active speaker/receiver (left-channel speaker)
1 x Power supply for active speaker/receiver
TO LEFT SPEAKER
1 x Wall-mount holder for active speaker/receiver universal
power supply
1 x Passive speaker (right-channel speaker)
2 x Terminal covers for active and passive speakers
6 x M3 x 8 self-tapping screws to attach terminal covers
Right/Passive
Speaker
RIGHT-CHANNEL SPEAKER
2 x Wall-mount rotatable brackets for active and passive speakers
(includes bar wrench and backup cords)
1 x Remote control
9
1 x Interconnect cable (1m/3.3 ft. RCA – RCA)
1 x Interconnect cable (1m/3.3 ft. RCA – 3,5mm (1/8-inch) mini plug)
10m/33 ft. x Speaker wire
1 x Owner’s manual (multilanguage)
Wireless Transmitter
ID
CODE
R INPUT L
1 2 3 4
A
C
D
B
4
CONNECTIONS
Notes: For the sake of simplicity, throughout this manual we have
used the term “source” when describing connections and operation.
This would apply to any device such as an A/V receiver, audio
component, computer or portable music player.
Step 2.
Determine the location of the surround speakers.
Subwoofer
The JBL On Air may be connected to your source in several ways.
First, determine how you would like to use the JBL On Air
Control 2.4G AW; then follow the setup instructions for that
application.
Left Front
Channel
Right Front
Channel
Center
Channel
Application 1
Adding surround speakers to a home theater system.
Continue reading the instructions for Application 1 below.
Application 2
Adding speakers to remote locations around your home.
Application 1
Adding surround speakers to a home theater system:
Couch
Determine if your source contains preamp outputs for rear/surround
channels, usually indicated by RCA-type jacks on the back of the
receiver labeled as “surround preout” (please refer to your source’s
owner’s manual to confirm whether it includes the preamp outputs).
If your receiver includes these outputs, follow the steps below.
If not, connection is not recommended.
Left
Surround
Channel
Right
Surround
Channel
Subwoofer
NOTE: Make sure power is turned off on all components.
Right Front
Channel
Step 1.
Connect the interconnect cable (included) to the left and right
surround/rear preamp outputs on the back of your source and the
Center
Channel
D
input on the transmitter module , as shown in Figure 1.
Right
Surround
Channel
Left Front
Channel
Left
Surround
Channel
RECEIVER/PROCESSOR
Figure 2. Place the active (left) speaker in the recommended
location for the left surround speaker.
Surround Channel
Preamp Outputs
R
L
ID
CODE
R
INPUT
L
1 2 3 4
Figure 1.
5
|